PVS 407D PoleVault Digital Switcher |
|
specification — HDMI inputs 1 to 6 |
|
Frame rate1 | 24, 25, 30, 50, or 60 fps |
Chroma sampling1 | 4:4:4, 4:2:2, or 4:2:0 |
Color bit depth1 | 8 bits per color |
Signal Type | HDMI 1.4, HDCP 1.4 |
Max. video data rate | 10.2 Gbps (3.4 Gbps per color) |
NOTE | 1Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate. |
|
NOTE | The PVS 407D must have firmware version 2.00 or greater for 4K support on all HDMI inputs, and firmware version 4.00 or greater for PVT HD RGB support. |
|
NOTE | This switcher is compatible with Extron Digital PVT HDMI RGB, PVT HD RGB, and PVT HDMI wallplates only. It is not compatible with other models of PVT wallplates. DO NOT connect to a data network. |
|
|
Video input |
Number/signal type | Inputs 1 - 6: HDMI (or DVI-D) digital video
Inputs 2 and 4 can be analog RGB |
Connectors | 2 female RJ-45
2 female HDMI, type A |
Termination standard | TIA/EIA T568B |
NOTE | Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. |
|
Video — Inputs 1 to 6 | |
Maximum data rate | 10.2 Gbps (3.4 Gbps per color) |
Maximum pixel clock | 300 MHz |
Resolution range | Up to 4096x2160 @ 30 Hz, 3840x2160 @ 30Hz,
4K/UHD @ 60 Hz with 4:2:0 Chroma subsampling |
Formats | RGB and YCbCr digital video |
Standards | DVI 1.0, HDMI 1.4, HDCP 1.4, CEA-861E |
|
Interconnection between PVT wallplates and PVS switcher |
Connector | 1 female RJ-45 per wallplate |
Termination standard | TIA/EIA T568A or T568B
Included Extron cables are T568B. |
Signal transmission distance | Up to 4096x2160 @ 30 Hz, 3840x2160 @ 30Hz, 4K/UHD @ 60 Hz with 4:2:0 Chroma subsampling. Up to 150' (46 m) for 2K rate, or up to 130' (40 m) for 4K/30 Hz, using Extron XTP DTP 24 cable. Standard included cable length is 35' (11 m). |
Cable requirements | Solid conductor, 24 AWG or better
400 MHz bandwith and above, STP (Shielded twisted pair) |
NOTE | Extron XTP DTP 24 shielded twisted pair cable is required for optimal performance. |
|
|
Video output |
Number/signal type | 1 single link HDMI (or DVI-D with appropriate HDMI-DVI adapter) |
Connectors | 1 female HDMI type A |
|
Audio input (see the PVT series wallplates audio specifications) |
Number/signal type | 2 proprietary signals from Extron PVT Series wallplate transmitters
1 stereo, balanced/unbalanced (input 7) |
Connectors | 2 female RJ-45
1 female 3.5 mm captive screw connector, 5-pole (input 7) |
|
Audio — preamplifier |
Input gain adjustment | -18 dB to +24 dB (default = 0 dB), adjustable per input via RS-232 |
Input level sensitivity | -10 dBV (0.316 Vrms) for maximum output before clipping |
Volume control range | 0 to -61 dB |
Crosstalk | <-85 dB @ 1 kHz (as a system with Extron PVT Series wallplates with 50' cables) |
Stereo channel separation | >80 dB @ 1 kHz (as a system with Extron PVT Series wallplates with 50' cables) |
Bass adjustment | -24 dB to +12 dB @ 50 Hz |
Treble adjustment | -24 dB to +12 dB @ 15 kHz |
|
Audio input — VoiceLift® receiver |
Number/signal type | 1 mono, balanced (mic) |
Connectors | 1 female RJ-45 |
Impedance | >10k ohms unbalanced/balanced, DC coupled |
Nominal level | -10 dBV (316 mVrms) |
Input gain/volume adjustment | -18 dB to +24 dB (default = -5 dB), (independently adjustable via front panel, RS-232, USB or Ethernet) |
Input level sensitivity | -10 dBV (316 mVrms) for maximum output before clipping when VoiceLift receiver volume is set to +24 dB |
|
Audio input — Aux |
Number/signal type | 1 mono, balanced or unbalanced |
Connectors | 1 female 3.5 mm captive screw connector, 3 pole |
Impedance | >10k ohms unbalanced/balanced, DC coupled |
Nominal level | -10 dBV (316 mVrms) |
Input gain/volume adjustment | -18 dB to +24 dB (default = 0 dB), (independently adjustable via front panel, RS-232, USB or Ethernet) |
Input level sensitivity | -10 dBV (316 mVrms) for maximum output before clipping when Aux volume is set to +24 dB |
|
Audio output — line-level output |
Number/signal type | 1 stereo/mono, balanced/unbalanced, fixed/variable |
Connector | (1) 3.5 mm captive screw connector, 5 pole |
Impedance | 50 ohms unbalanced, 100 ohms balanced |
Gain error | ±0.8 dB channel to channel |
Maximum level (600 ohms) | +8 dBu, balanced, at <0.1% THD+N |
NOTE | Unbalanced outputs produce 6 dB of attenuation. Balanced output has unity gain/attenuation. |
|
|
Audio output — power amplifier |
Number/signal type | 1 stereo or dual mono (default), 2 channels total |
Connectors | (1) 5.0 mm captive screw connector, 4 pole |
Load impedance | 4/8 ohms, single channel or stereo |
Amplifier type | Class D |
Frequency response | 20 Hz to 20 kHz, +1 dB/-3 dB @ 1 watt output, 8 ohm load |
THD + Noise | 0.2% @ 1 kHz at nominal level (1 watt, 8 ohm load) |
S/N | >67 dB, 20 Hz to 20 kHz at maximum output (unweighted), 8 ohms (as a system with Extron PVT Series wallplates with 50' cables) |
Output power | 25 watts rms per channel, 4/8 ohms, 1 kHz, 1% THD |
Damping factor | >75 @ 8 ohms |
|
Communications — switcher |
NOTE | The front panel USB port and the rear panel RS-232 port are independent of each other and can be used at the same time. |
|
NOTE | Any 1 of the 4 rear panel Ethernet (RJ-45) connectors can be used for Ethernet control of the switcher. |
|
Serial host control ports | 1 bidirectional RS-232: 1 rear panel 3.5 mm captive screw connector, 3 pole |
Baud rate and protocol | 9600 baud, 8 data bits, 1 stop bit, no parity |
Serial control pin configurations | Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND |
Ethernet control port | 1 female RJ-45 connector |
Ethernet data rate | 10/100Base-T, half/full duplex with autodetect |
Ethernet protocol | ARP, ICMP (ping), IP, TCP, UDP, DHCP, HTTP, SMTP, Telnet |
USB control port | 1 front panel female mini USB B |
USB standards | USB 2.0, high speed |
Paging sensor connector | (1) 3.5 mm captive screw connector, 3 pole |
IR pass-through control port | (1) 3.5 mm captive screw connector, 2 pole |
Program control | Extron Configuration Software for Windows
Extron Simple Instruction Set (SIS) |
|
Ethernet ports |
Switch type | Unmanaged |
Standards | IEEE 802.3, IEEE 802.3u, IEEE 802.3x |
Recommended cable type | For 10Base-T: UTP CAT 3 or better For 100Base-T: UTP CAT 5 or better |
Ethernet ports | 4 female RJ-45 (with built-in link/speed and activity LEDs) |
Ethernet data rate | 10/100Base-T (10/100 Mbps) with autodetect |
Ethernet protocol | ARP, ICMP (ping), IP, TCP, DHCP, HTTP, Telnet |
MAC address table | 1 k |
Buffer | 64 kB |
Switching method | Store and forward |
MDI/MDI-X selection | Automatic |
PoE | Not supported |
SNMP | Not supported |
QoS | No |
LACP | Not supported |
Layer | 2 |
Port mirroring | Not supported |
VLAN | Not supported |
Program control | Extron Configuration Software for Windows
Extron Simple Instruction Set (SIS)
Microsoft Internet Explorer, Telnet |
|
General |
Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 4 A, 48 watts
or 12 VDC, 4.2 A, 50 watts |
Power input requirements | 12 VDC, 3 A |
Power consumption | |
PVS, WVS, and PLS 200 series | |
Device | 23.5 watts, 12 VDC |
Device and power supply | 27.1 watts, 110-240 VAC, 50-60 Hz |
PVS, WVS, and PLS 400 series | |
Device | 30.4 watts, 12 VDC |
Device and power supply | 37.1 watts, 110-240 VAC, 50-60 Hz |
Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
Cooling | Fan, air flows from right to left (as viewed from front panel) |
Thermal dissipation | |
PVS, WVS, and PLS 200 series | |
Device | 32.0 BTU/hr |
Device and power supply | 44.4 BTU/hr |
PVS, WVS, and PLS 400 series | |
Device | 31.8 BTU/hr |
Device and power supply | 54.7 BTU/hr |
Mounting | |
Wall mount | Yes, with optional wall mounting kit |
Pole mount | Yes, with optional pole mounting kit |
Ceiling mount | Yes, with optional ceiling mount |
Enclosure type | Metal |
Enclosure dimensions | 1.9" H x 13.5" W x 3.5" D
(4.8 cm H x 34.3 cm W x 8.9 cm D) |
Product weight | 1.7 lbs (0.77 kg), plus power supply (1.1 lb [0.5 kg]) |
Regulatory compliance | CE, C-Tick, c-UL, FCC Class A, ICES, UL, VCCI
UL listed for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60065 for safety.
Complies with the appropriate requirements of RoHS, WEEE |
Warranty | 3 years parts and labor |
NOTE | All nominal levels are at ±10%. |
|
NOTE | Specifications are subject to change without notice. |
|
(3994-D4) |